B
Workshop Agenda
A Workshop on the Frontiers of Mechanistic Data-Driven Modeling for
Additive Manufacturing
October 24–26, 2018
Neue Materialien Fürth GmbH
Dr.-Mack-Straße 81, Technikum 1, 6th Floor
Fürth, Germany
Day 1: October 24
9:00 a.m. | Welcome from the Co-Chairs |
Carolin Körner, Co-Chair, Friedrich-Alexander Universität Erlangen-Nürnberg |
|
Wing Kam Liu, Co-Chair, Northwestern University |
|
9:20 a.m. | Opening Comments from the Sponsors |
R. Allen Roach, Sandia |
|
Richard Ricker, NIST |
|
9:40 a.m. | Opening Comments from the National Academies |
Michelle Schwalbe, Board on Mathematical Sciences and Analytics |
|
Erik Svedberg, National Materials and Manufacturing Board |
SESSION 1: MEASUREMENTS AND MODELING FOR PROCESS MONITORING AND CONTROL
10:00 a.m. | Introduction to Session 1 |
Bianca Colosimo, Politecnico di Milano |
|
10:10 a.m. | Measurement Science for Process Monitoring and Control |
Jarred Heigel, National Institute of Standards and Technology |
|
10:40 a.m. | Break |
11:00 a.m. | Process Simulation as a Complement of Process Monitoring1 |
Daniel Reznik, Siemens |
|
11:30 a.m. | Lunch |
12:30 p.m. | Panel Discussion |
|
|
Panelists: | |
Bianca Colosimo, Politecnico di Milano |
|
Ben Dutton, Manufacturing Technology Centre |
|
Jarred Heigel, National Institute of Standards and Technology |
|
Daniel Reznik, Siemens |
|
Kilian Wasmer, Empa |
|
Amit Surana, United Technologies Research Center |
|
2:00 p.m. | Break |
SESSION 2: DEVELOPING MODELS TO REPRESENT MICROSTRUCTURE EVOLUTION, ALLOY DESIGN, AND PART SUITABILITY
2:30 p.m. | Introduction to Session 2 |
Lyle Levine, National Institute of Standards and Technology | |
___________________
1 Unable to attend.
2:35 p.m. | Measurements for Additive Manufacturing of Metals |
Lyle Levine, National Institute of Standards and Technology |
|
3:05 p.m. | Break |
3:30 p.m. | Predicting Material State and Performance of Additively Manufactured Parts |
Kyle Johnson, Sandia National Laboratories |
|
4:00 p.m. | Panel Discussion |
|
|
Panelists: | |
Lyle Levine, National Institute of Standards and Technology |
|
Eric Jägle, Max Planck Institute |
|
Kyle Johnson, Sandia National Laboratories |
|
Christian Leinenbach, Empa |
|
Deniece Korzekwa, Los Alamos National Laboratory |
|
Annett Seide, MTU Aero Engines |
|
John Turner, Oak Ridge National Laboratory |
|
5:30 p.m. | Conclude Sessions |
Day 2: October 25
9:00 a.m. | Recap of Day 1; Major Themes and Overview for the Day |
Session 1: Bianca Colosimo |
|
Session 2: Lyle Levine |
SESSION 3: MODELING ASPECTS OF PROCESS AND MACHINE DESIGN
9:30 a.m. | Introduction to Session 3 |
Tahany El-Wardany, United Technologies Research Center |
|
9:40 a.m. | Current State of Commercial Powder-Bed Additive Machines—Improvements Needed to Minimize Build-to-Build Variability |
Ade Makinde, General Electric Global Research Center, with support from Johannes Henrich Schleifenbaum, Fraunhofer Institute for Laser Technology, and Shoufeng Yang, KU Leuven | |
10:10 a.m. | Break |
10:30 a.m. | Modeling Challenges and Opportunities at the Part Level |
Jian Cao, Northwestern University, with support from Ranadip Acharya, United Technologies Research Center, and Mustafa Megahed, ESI Group | |
11:00 a.m. | Panel Discussion |
|
|
Panelists: | |
Tahany El-Wardany, United Technologies Research Center |
|
Ranadip Acharya, United Technologies Research Center |
|
Jian Cao, Northwestern University |
|
Ade Makinde, General Electric Global Research Center |
|
Mustafa Megahed, ESI Group |
|
Johannes Henrich Schleifenbaum, Fraunhofer Institute for Laser Technology |
|
Michael Schmidt, Friedrich-Alexander Universität Erlangen-Nürnberg |
|
Shoufeng Yang, KU Leuven |
|
12:30 p.m. | Lunch |
SESSION 4: ACCELERATING PRODUCT AND PROCESS QUALIFICATION AND CERTIFICATION
1:30 p.m. | Introduction to Session 4 |
Paolo Gennaro, GF Precicast Additive SA |
|
1:35 p.m. | Process Qualification and Technological Validation, from Casting to Additive |
Paolo Gennaro, GF Precicast Additive SA |
|
2:05 p.m. | Modeling and Simulation |
Michel Delanaye,2 GeonX |
|
2:35 p.m. | Break |
___________________
3:00 p.m. | Panel Discussion |
|
|
Panelists: | |
Paolo Gennaro, GF Precicast Additive SA |
|
Vincent Paquit, Oak Ridge National Laboratory |
|
Jens Telgkamp, Airbus Operations GmbH |
|
Michel Delanaye, GeonX |
|
David Teter, Los Alamos National Laboratory |
|
Richard Ricker, National Institute of Standards and Technology |
|
5:00 p.m. | Conclude Presentations and Discussions |
Day 3: October 26
9:00 a.m. | Recap of Day 2; Major Themes and Overview for the Day |
Session 3: Tahany El-Wardany | |
Session 4: Paolo Gennaro | |
9:30 a.m. | Breakout Groups |
|
|
12:00 p.m. | Lunch (with Breakout Groups) |
1:00 p.m. | Breakout Groups Report Back |
2:30 p.m. | Final Comments from Co-Chairs and Sponsors |
Carolin Körner, Co-Chair, Friedrich-Alexander Universität Erlangen-Nürnberg |
|
Wing Kam Liu, Co-Chair, Northwestern University |
|
Sponsors’ Representatives |
|
3:00 p.m. | Adjourn Workshop |