National Academies Press: OpenBook

Twenty-Third Symposium on Naval Hydrodynamics (2001)

Chapter: Steady-State Hydrodynamics of High-Speed Vessels with a Transom Stern

« Previous: HULL DESIGN by CAD/CFD SIMULATION
Suggested Citation:"Steady-State Hydrodynamics of High-Speed Vessels with a Transom Stern." National Research Council. 2001. Twenty-Third Symposium on Naval Hydrodynamics. Washington, DC: The National Academies Press. doi: 10.17226/10189.
×
Page 191
Suggested Citation:"Steady-State Hydrodynamics of High-Speed Vessels with a Transom Stern." National Research Council. 2001. Twenty-Third Symposium on Naval Hydrodynamics. Washington, DC: The National Academies Press. doi: 10.17226/10189.
×
Page 192
Suggested Citation:"Steady-State Hydrodynamics of High-Speed Vessels with a Transom Stern." National Research Council. 2001. Twenty-Third Symposium on Naval Hydrodynamics. Washington, DC: The National Academies Press. doi: 10.17226/10189.
×
Page 193
Suggested Citation:"Steady-State Hydrodynamics of High-Speed Vessels with a Transom Stern." National Research Council. 2001. Twenty-Third Symposium on Naval Hydrodynamics. Washington, DC: The National Academies Press. doi: 10.17226/10189.
×
Page 194
Suggested Citation:"Steady-State Hydrodynamics of High-Speed Vessels with a Transom Stern." National Research Council. 2001. Twenty-Third Symposium on Naval Hydrodynamics. Washington, DC: The National Academies Press. doi: 10.17226/10189.
×
Page 195
Suggested Citation:"Steady-State Hydrodynamics of High-Speed Vessels with a Transom Stern." National Research Council. 2001. Twenty-Third Symposium on Naval Hydrodynamics. Washington, DC: The National Academies Press. doi: 10.17226/10189.
×
Page 196
Suggested Citation:"Steady-State Hydrodynamics of High-Speed Vessels with a Transom Stern." National Research Council. 2001. Twenty-Third Symposium on Naval Hydrodynamics. Washington, DC: The National Academies Press. doi: 10.17226/10189.
×
Page 197
Suggested Citation:"Steady-State Hydrodynamics of High-Speed Vessels with a Transom Stern." National Research Council. 2001. Twenty-Third Symposium on Naval Hydrodynamics. Washington, DC: The National Academies Press. doi: 10.17226/10189.
×
Page 198
Suggested Citation:"Steady-State Hydrodynamics of High-Speed Vessels with a Transom Stern." National Research Council. 2001. Twenty-Third Symposium on Naval Hydrodynamics. Washington, DC: The National Academies Press. doi: 10.17226/10189.
×
Page 199
Suggested Citation:"Steady-State Hydrodynamics of High-Speed Vessels with a Transom Stern." National Research Council. 2001. Twenty-Third Symposium on Naval Hydrodynamics. Washington, DC: The National Academies Press. doi: 10.17226/10189.
×
Page 200
Suggested Citation:"Steady-State Hydrodynamics of High-Speed Vessels with a Transom Stern." National Research Council. 2001. Twenty-Third Symposium on Naval Hydrodynamics. Washington, DC: The National Academies Press. doi: 10.17226/10189.
×
Page 201
Suggested Citation:"Steady-State Hydrodynamics of High-Speed Vessels with a Transom Stern." National Research Council. 2001. Twenty-Third Symposium on Naval Hydrodynamics. Washington, DC: The National Academies Press. doi: 10.17226/10189.
×
Page 202
Suggested Citation:"Steady-State Hydrodynamics of High-Speed Vessels with a Transom Stern." National Research Council. 2001. Twenty-Third Symposium on Naval Hydrodynamics. Washington, DC: The National Academies Press. doi: 10.17226/10189.
×
Page 203
Suggested Citation:"Steady-State Hydrodynamics of High-Speed Vessels with a Transom Stern." National Research Council. 2001. Twenty-Third Symposium on Naval Hydrodynamics. Washington, DC: The National Academies Press. doi: 10.17226/10189.
×
Page 204
Suggested Citation:"Steady-State Hydrodynamics of High-Speed Vessels with a Transom Stern." National Research Council. 2001. Twenty-Third Symposium on Naval Hydrodynamics. Washington, DC: The National Academies Press. doi: 10.17226/10189.
×
Page 205

Below is the uncorrected machine-read text of this chapter, intended to provide our own search engines and external engines with highly rich, chapter-representative searchable text of each book. Because it is UNCORRECTED material, please consider the following text as a useful but insufficient proxy for the authoritative book pages.

About this PDF file: This new digital representation of the original work has been recomposed from XML files created from the original paper book, not from the original typesetting files. Page breaks are true to the original; line lengths, word breaks, heading styles, and other typesetting-specific formatting, however, cannot be retained, and some typographic errors may have been accidentally inserted. Please use the print version of this publication as STEADY-STATE HYDRODYNAMICS OF HIGH-SPEED VESSELS WITH A TRANSOM STERN 191 Steady-State Hydrodynamics of High-Speed Vessels with a Transom Stern Lawrence J.Doctors (The University of New South Wales, Australia) Alexander H.Day (The University of Glasgow, Scotland) ABSTRACT The inviscid linearized near-field solution for the flow past a vessel with a transom stern is developed within the framework of classical thin-ship theory. However, the innovation in the current approach is that the hollow in the water behind the stern is represented here by a virtual extension to the usual hull-centerplane source distribution. In the present work, the near-field solution to the flow using the thin-ship approximation must be computed. This idea clearly demands a considerable addition to the complexity of the numerical solution which contrasts with the traditional farfield method employed by Michell (1898). The computer program functions by iterating the geometry of the hollow until the criterion of atmospheric pressure on the surface of the hollow is zero. In addition, the iteration procedure includes adjusting the sinkage and trim of the vessel until it is in equilibrium. The latter component of the computation utilizes an integration of the resulting pressure distribution over the wetted surface of the vessel in an entirely consistent manner. Comparison of the theoretical results with a systematic series of twelve models shows excellent correlation with the towing-tank data. Indeed, the behavior of this approach appears to be much more robust than, for example, that of the Neumann-Kelvin problem and some fully nonlinear analyses. INTRODUCTION Literature Review Previous work on the subject of prediction of resistance of marine vehicles, such as monohulls and catamarans, has shown that the trends in the curve of total resistance with respect to speed can be predicted with excellent accuracy, using the traditional Michell (1898) wave-resistance theory, together with a suitable formulation for the component of frictional resistance. There have been further enhancements to this wave-resistance theory. These enhancements include the influences of finite depth and finite width of the canal by Lunde (1951) and Sretensky (1936). A recent justification for this research, in which linearized free-surface conditions are employed, is the very encouraging comparisons that were made by Doctors and Renilson (1993) for monohulls and catamarans with closed or pointed sterns and by Sahoo, Doctors, and Renilson (1999) for monohulls with open or transom sterns. One difficulty has been that nonlinear and viscous-wave effects are not included and, consequently, the correlation between theory and experiment has not been sufficiently good for the purpose of practical ship design. For this reason, a considerable effort has been invested in recent years in the development of fully nonlinear computer codes. The complete nonlinear kinematic body-boundary condition and the nonlinear free-surface kinematic and dynamic boundary conditions are satisfied in these programs. There has been excellent progress with such computer programs and they may eventually be developed to the stage where they can be used for hull-form development. Currently, the execution time is too long for one to contemplate any realistic optimization of hull forms. Consequently, any type of optimization, such as the genetic-algorithm method of Doctors and Day (1995) and Day and Doctors (1997b) is not possible. This is because of the requirement to evaluate the resistance many thousands of times during the practical design process. the authoritative version for attribution.

About this PDF file: This new digital representation of the original work has been recomposed from XML files created from the original paper book, not from the original typesetting files. Page breaks are true to the original; line lengths, word breaks, heading styles, and other typesetting-specific formatting, however, cannot be retained, and some typographic errors may have been accidentally inserted. Please use the print version of this publication as STEADY-STATE HYDRODYNAMICS OF HIGH-SPEED VESSELS WITH A TRANSOM STERN 192 Figure 1: Definition of the Problem (a) Geometry and Forces A further point is that more sophisticated computer codes, such as those briefly alluded to above, do not always lead to more accurate or reliable predictions for sensitive quantities, such as resistance. This is because resistance can be affected markedly by minor inaccuracies in the computed pressure distribution over the surface of the hull. A revealing study of this troubling possibility was published by Sahoo, Doctors, and Renilson (1999). It was demonstrated there that more reliable predictions for the resistance were obtained from the consistent linearized approach, than from a modern nonlinear code, for a set of fourteen modern high-speed vessels with transom sterns. Indeed, the linearized approach gave predictions which were within 5% for most of the test cases, while the errors from the competing nonlinear method were typically an order of magnitude greater. Further reductions in the errors inherent in the linearized theory can be obtained in a most practical manner by means of very easily estimated correction factors for the wave resistance and for the frictional resistance. Examples of this research were published by Doctors (1998a, 1998b, and 1998c). Current Work These principles were advanced in the research presented by Doctors and Day (1997). Firstly, transom-stern effects were included in the theory by accounting for the hollow in the water behind the vessel. This work was essentially a development of the ingenious and practical approach first presented by Molland, Wellicome, and Couser (1994) and Couser, Wellicome, and Molland (1998). Figure 1: Definition of the Problem (b) Centerplane Paneling There, a simple virtual extension to the hull behind the transom was constructed in the computer program. The wave resistance for the vessel was deduced on the basis of an application of the Michell integral to the entire model and its extension, together with an estimate of the hydrostatic resistance due to the existence of the dry transom. The extension was allowed to grow in length with increasing forward speed of the vessel in a physically plausible manner as detailed by Doctors and Day (1997). A more sophisticated enhancement of this work was presented recently by Doctors and Day (2000). The local flow field was computed on the basis of the linearized theory. This permitted the squat (sinkage and trim) to be determined; the authoritative version for attribution. excellent correlation with experimental data was obtained in this way. However, the shape of the hollow was still determined in a heuristic manner. It is the purpose of the current research effort to iterate the shape of this transom-stern hollow in order to improve the accuracy of the approach even further. THEORY Definition of the Problem Figure 1(a) shows a typical arrangement for a vessel traveling at a constant speed U in calm

About this PDF file: This new digital representation of the original work has been recomposed from XML files created from the original paper book, not from the original typesetting files. Page breaks are true to the original; line lengths, word breaks, heading styles, and other typesetting-specific formatting, however, cannot be retained, and some typographic errors may have been accidentally inserted. Please use the print version of this publication as STEADY-STATE HYDRODYNAMICS OF HIGH-SPEED VESSELS WITH A TRANSOM STERN 193 water. The x, y, z coordinate system is also depicted. The water is unbounded laterally (in the y direction) as well as having infinite depth. The components of the forces acting on the vessel are indicated. The vessel can either be self propelled or be towed. In the former case, the thrust from the propeller or the water jet acts along a defined line of action relative to the coordinate system attached to the vessel. Thus, the direction and position of the thrust line vary with the speed of the vessel. In the latter case, the vessel is towed at the specified speed from a particular point in the hull. Hence, the line of action of the thrust is longitudinal, but the line moves vertically in sympathy with the sinkage and trim. Discretization of the Hull Further details of the problem are provided in Figure 1(b). Here, the centerplane paneling is seen to overlay the hull and the hollow in the water behind the transom stern. The panels or elements possess a flat facet and a rectangular base. They are employed, in particular, for the purpose of the numerical calculation of the pressure, or profile, resistance. These elements are chosen in order to approximate the centerplane area of the hull and the hollow as closely as possible. The longitudinal and vertical slope of the facets of the elements match the corresponding values of the hull surface in a root- mean-square sense. This type of panel is algebraically simpler than the “pyramids” or “tents” which were previously employed by Day and Doctors (1997b) and Doctors and Day (1997a), for example. The use of flat facets implies a higher level of discontinuity on the hull surface. On the other hand, numerical convergence tests for wave resistance, based on the two types of panels, showed that a similar number of panels was required in either case; namely, 40 panels in the longitudinal direction and 8 panels in the vertical direction. Equations for the Potential We start in the traditional manner by utilizing the potential whose gradient gives the perturbation velocity. The potential satisfies the Laplace equation throughout the fluid domain: (1) The linearized kinematic free-surface condition, namely (2) states that any water particles on the free surface remain there. Here, ζ is the elevation of the free surface measured upward from its undisturbed position z=0. In addition, the Bernoulli equation provides the linearized dynamic free-surface condition (3) in which g is the acceleration due to gravity. The Rayleigh (1883) artificial viscosity µ, which is assumed to be vanishingly small and positive, has been introduced in this technique in order to impose the radiation condition, which states that waves must be propagated downstream. De Prima and Wu (1957) gave a clear description of this concept. Elimination of ζ from Equations (2) and (3) yields the linearized combined free-surface condition: (4) Finally, the “bed” kinematic boundary condition states that (5) Potential-Flow Solution The solution for the flow past the vessel and its transom-stern hollow is obtained by using the equivalent centerplane- source distribution. This distribution is assembled from panels, as noted earlier, while the panels are constructed from the elementary Kelvin point source. The potential due to a Kelvin point source of strength Q, obtained by Wehausen and Laitone (1960, p.484, Equation (13.36)), is (6) where we have defined the radial distances (7) (8) the authoritative version for attribution.

About this PDF file: This new digital representation of the original work has been recomposed from XML files created from the original paper book, not from the original typesetting files. Page breaks are true to the original; line lengths, word breaks, heading styles, and other typesetting-specific formatting, however, cannot be retained, and some typographic errors may have been accidentally inserted. Please use the print version of this publication as STEADY-STATE HYDRODYNAMICS OF HIGH-SPEED VESSELS WITH A TRANSOM STERN 194 Figure 2: Sample Ship Models (a) Lego Ship Models 7 Figure 2: Sample Ship Models (b) Lego Ship Models 11 and 8 and 12 and the wave term is (9) Here, the circular wave number is the fundamental wave number is and the complex horizontal wave number is The first term in Equation (6) can be integrated for a constant-strength-source panel oj and a unit-constant- longitudinal-slope field panel in the so-called Galerkin manner. The result for the induced longitudinal gradient of the potential at the field panel is (10) in which the weighting factor is given by the formula and the required arguments in the special function G4 are defined by The four special functions needed for this analysis are interrelated by spatial integrations as follows: (11) (12) (13) (14) The second term in Equation (6) can be integrated in a very similar manner. The third term can also be integrated with respect to the wavenumber k, as well as with re the authoritative version for attribution.

About this PDF file: This new digital representation of the original work has been recomposed from XML files created from the original paper book, not from the original typesetting files. Page breaks are true to the original; line lengths, word breaks, heading styles, and other typesetting-specific formatting, however, cannot be retained, and some typographic errors may have been accidentally inserted. Please use the print version of this publication as STEADY-STATE HYDRODYNAMICS OF HIGH-SPEED VESSELS WITH A TRANSOM STERN 195 spect to the spatial coordinates, to yield (15) in which the argument of the function F4 is given by The special complex wave function F4 is closely related to the exponential integral and was defined by Doctors and Beck (1987). The zeroth wave function is (16) and the complex exponential integral is while the other four complex wave functions are (17) (18) (19) (20) Modeling of the Hollow The hollow is considered to be a virtual extension to the hull of the vessel and is modeled by a continuation of the centerplane source distribution. The determination of the shape of the centerplane of this hollow represents a vital part of the hydrodynamic problem. The length of the hollow is initially estimated by the method detailed by Doctors and Day (1997). That is, the equivalent radial position of a point in the region of the hollow behind the stern is taken to be (21) We next state that the effective trajectory of a particle of water on the surface of the hollow is parabolic in nature and that it has parametric coordinates as follows: (22) (23) in which xtran and rtran are the coordinates of the equivalent springing point of the hollow on the transom girth. Equations (22) and (23) can be solved by setting r=0 to yield the location of the vertex, or rooster tail, of the hollow xholl. Hence, the length of the hollow is evaluated as: (24) In the current enhanced technique, the initial estimated profile of the hollow is assumed to be defined by the parabola the authoritative version for attribution. that springs longitudinally from the bottom of the transom and meets the vertex on the (undisturbed) free surface. Forces and Moment on the Vessel One first assumes that the attitude of the vessel is the same as its static attitude, that is, with zero sinkage and trim. The required source strength is computed using the standard thin-ship result, namely, in which b is the local beam. The total gradient of the potential at the field panel i is next computed, by summing the contributions from the source panels presented in Equations (10) and (15). From this, one can determine the pressure on the surface of the hull, as follows: (25)

About this PDF file: This new digital representation of the original work has been recomposed from XML files created from the original paper book, not from the original typesetting files. Page breaks are true to the original; line lengths, word breaks, heading styles, and other typesetting-specific formatting, however, cannot be retained, and some typographic errors may have been accidentally inserted. Please use the print version of this publication as STEADY-STATE HYDRODYNAMICS OF HIGH-SPEED VESSELS WITH A TRANSOM STERN 196 where ρ is the density of the water and z is the elevation of the centroid of the field panel. Next, the three components of the generalized forces on the vessel (pressure resistance, sinkage force, and bow-up moment) are then found from this pressure distribution: (26) in which the generalized surface slope is given by the formula (27) Finally, the total resistance can be found by the simple summation (28) in which R P is the pressure resistance computed from Equation (26), RF is the frictional resistance estimated from the 1957 International Towing Tank Committee (ITTC) formula, described by Lewis (1988, Section 3.5), and RA is the correlation resistance. Equilibrium of the Vessel At any stage of the iteration for the equilibrium of the vessel, one can estimate the corrections to the sinkage and trim angle (positive bow down), with respect to the longitudinal center of flotation LCF: (29) (30) The additional symbols introduced here are SP the sinkage pressure force, W the weight of the vessel, Zprop the vertical component of the propulsion force (equal to zero in the case of the vessel being towed), AW the static waterplane area, zP the vertical lever arm for the pressure resistance (equal to zero), xP the longitudinal lever arm for the pressure sinkage force (equal to −LCF), MP the bow-up pressure moment, xprop the longitudinal lever arm for the propulsion force, zprop the vertical lever arm for the propulsion force, Xprop the longitudinal component of the propulsion force, zF the vertical arm for the frictional force (measured to the centroid of the wetted surface), zstab the vertical lever arm to the stabilizers, Rstab the resistance of the stabilizers (zero in the current work), LCB the longitudinal center of buoyancy, and the longitudinal metacentric height. The sinkage at the coordinate origin x=0 and the trim are (31) (32) where L is the length of the vessel. For simplicity, the hydrostatic stiffness coefficients were used for iterating the sinkage and trim of the vessel, as seen in Equations (29) and (30). The use of the ideally consistent hydrodynamic stiffness coefficients would have posed a somewhat major computing challenge. Relative convergence of 1×10−4 could be obtained within about eight iterations; once equilibrium is achieved, there is no error introduced by the simpler approach. Iteration of the Hollow The pressure at any point on the hollow is given by a formula of the type of Equation (25). If there are Nholl panels that lie on the centerplane of the hollow, then there will be the same number of panel collocation points at which we desire the pressure to be zero (or atmospheric). The Kutta condition is applied by extending this requirement to include the last column of panels on the surface of the hull next to the transom. In addition, we must impose the closure conditions. Because the panels are of uniform rectangular shape, we just the authoritative version for attribution. require the source strengths σj along a longitudinal line of panels (z is constant) to sum to zero. A set of overconstrained linear equations is then set up, in which the pressures are minimized

About this PDF file: This new digital representation of the original work has been recomposed from XML files created from the original paper book, not from the original typesetting files. Page breaks are true to the original; line lengths, word breaks, heading styles, and other typesetting-specific formatting, however, cannot be retained, and some typographic errors may have been accidentally inserted. Please use the print version of this publication as STEADY-STATE HYDRODYNAMICS OF HIGH-SPEED VESSELS WITH A TRANSOM STERN 197 in a least-square sense while the closure conditions are satisfied exactly. Next, the secant method is employed in which the length of the hollow is adjusted until the average pressure on the surface of the hollow is minimized. The error in the average pressure on the surface of the hollow after the iteration process was typically one percent of the hydrostatic pressure at the keel of the vessel. In summary, it can be seen that the methodology used in this work is analogous to that underlying the solution of the problem of symmetric two-dimensional cavitating flow behind a body possessing a bluff stern, as presented by Newman (1980, Section 5.13, pp 208–215). However, the following extensions have been introduced: 1. Three-dimensions; 2. Free-surface; 3. Equilibrium of the body; 4. Iteration of cavity shape. Simplistic Resistance The simpler and traditional approach to thin-ship resistance has been to utilize the Michell (1898) result for the resistance applied to the vessel, together with a suitable formulation for the shape of the hollow. Examples are the work of Day and Doctors (1997a), Day, Doctors, and Armstrong (1997), Doctors and Day (1997), and Doctors (1999). This approach leads to the following estimate of the total resistance: (33) in which R W is the wave resistance, computed as (34) where the complex Michell wave function is (35) Table 1: Lego Ship Models (Common Data) Item Symbol Value Lbow Length of bow section 0.750 m B Waterline beam 0.150 m T Draft 0.09375 m CM Maximum-section coef. 0.6667 with S0 being the centerplane area. The complex wave function for a panel with center is (36) Finally, RH is the so-called hydrostatic resistance, resulting from the imbalance of the hydrostatic pressure owing to the transom being “dry”: (37) in which T tran is the draft at the transom. This simplistic approach to resistance provides an identical result to that from the near-field approach described earlier in this paper, in the case of a vessel with no transom. LEGO SHIP MODEL SERIES This series of hulls was developed with the intention of studying the hydrodynamics of transom sterns. Doctors the authoritative version for attribution. (1998a) provided the details of the hull segments from which the ship models were assembled. There was a total of seven segments. The bow and stern segments have parabolic waterplanes. The bow, stern, and parallel-middle-body segments all possess parabolic cross sections. Figure 2 shows views of four of the test models. Table 1 and Table 2 list the details of all twelve of these so-called Lego Ship Models. RESULTS Numerical Convergence Tests The wave resistance of a vessel without a transom stern, computed according to Equations (34) to (36), is identical to that computed

About this PDF file: This new digital representation of the original work has been recomposed from XML files created from the original paper book, not from the original typesetting files. Page breaks are true to the original; line lengths, word breaks, heading styles, and other typesetting-specific formatting, however, cannot be retained, and some typographic errors may have been accidentally inserted. Please use the print version of this publication as STEADY-STATE HYDRODYNAMICS OF HIGH-SPEED VESSELS WITH A TRANSOM STERN 198 using the considerably more elaborate near-field solution. This assumes the same discretization of the hull centerplane and the use of the same mesh in the wave-angle integration. Thus, one has an interesting and powerful check of the computer coding. Table 2: Lego Ship Models (Variable Data) Length of Parallel Middle Body LP (m) Length of Run LR (m) Length L (m) Prismatic Coefficient CP Ship Model 1 0.000 0.0000 0.7500 0.6666 2 0.000 0.1875 0.9375 0.7290 3 0.000 0.3750 1.1250 0.7499 4 0.000 0.5625 1.3125 0.7290 5 0.750 0.0000 1.5000 0.8332 6 0.750 0.1875 1.6875 0.8494 7 0.750 0.3750 1.8750 0.8499 8 0.750 0.5625 2.0625 0.8275 9 1.500 0.0000 2.2500 0.8888 10 1.500 0.1875 2.4375 0.8957 11 1.500 0.3750 2.6250 0.8928 12 1.500 0.5625 2.8125 0.8735 The four parts of Figure 3 show a test of convergence for Lego Ship Model 7 for four physical parameters of interest. These parameters are the total resistance RT, the sinkage s, the trim t, and the hollow length Lholl. These parameters have been rendered dimensionless using the weight of the ship W or its length L, as appropriate. It can be seen that using 40 panels longitudinally and 8 panels vertically is sufficient for the current purpose. In the same vein, one requires 32 points for half the range of the θ integration in Equation (15) to obtain reasonable convergence of the results. The annotation Holl=P, K indicates that in this case the pressure condition on the surface of the hollow and the Kutta condition on the transom were satisfied. Also, Free=Yes states that the model was free to sink and trim. The slenderness coefficient L/ ∇ 1/3 is also printed on the plots. Resistance Components Figure 4 depicts the theoretical computations of the various resistance components referred to above, for four of the ship models. These show the hydrostatic resistance RH, the pressure resistance RP, the frictional resistance RF, the total resistance RT, and the total experimental resistance RT,E. In general, the correlation between the theory and the experiments is good at the higher speeds, which are of practical significance, that is, for a Froude number F of 0.6 or greater. The disagreement is greatest at the lower speeds, where the transom would in reality be partly wetted, thus reducing the drag. This phenomenon has been ignored in the current calculations. An indication of the error involved at these low speeds is just the hydrostatic resistance; it can be observed that subtracting this quantity would bring the theoretical calculations into line with the experimental data. This process was, in fact, done by Doctors (1998d) in an approximate manner. Comparison with Experiments Figure 5 shows the specific resistance R/W for the four Lego Ship Models. The different methods used are respectively: the simplified method of Doctors and Day (1997) (Holl=Simp), the simplified method of Doctors and Day (2000) with the vessel also free to sink and trim (Free=Yes), the current method with the pressure and the Kutta conditions applied (Holl=P, K), and the current method with the pressure and Kutta conditions applied and also the hollow length Lholl iterated to minimize this pressure (Holl=P, K, L). It is noteworthy that the main factor of importance is the need to permit the vessel to sink and trim in order to find its equilibrium position. The other various enhanced versions of the theory appear to offer little, if any, improved correlation with the experiments. We next examine Figure 6, which shows a comparison of the theoretical predictions and experiments for the dimensionless sinkage s/L for the four Lego Ship Models. The second, third, and fourth methods are considered here. The first method, of course, does not include sinkage and trim at all. Again, we observe that the simplified method which permits determining the equilibrium of the vessel, namely that of Doctors and Day (2000), is as effective as the current more sophisticated approaches. the authoritative version for attribution.

About this PDF file: This new digital representation of the original work has been recomposed from XML files created from the original paper book, not from the original typesetting files. Page breaks are true to the original; line lengths, word breaks, heading styles, and other typesetting-specific formatting, however, cannot be retained, and some typographic errors may have been accidentally inserted. Please use the print version of this publication as STEADY-STATE HYDRODYNAMICS OF HIGH-SPEED VESSELS WITH A TRANSOM STERN 199 Figure 3: Convergence Tests (a) Resistance Figure 3: Convergence Tests (b) Sinkage Figure 3: Convergence Tests (c) Trim Figure 3: Convergence Tests (d) Hollow Length Similar sentiments can be expressed with regard to Figure 7, which presents the dimensionless trim t/L for the four Lego Ship Models. Again, the simplified method which includes the determination of the equibrium of the vessel, is as accurate as the current methods. Finally, we present Figure 8, which shows the dimensionless hollow length L holl/L for the four Lego Ship Models. It is curious to note that there is little significant difference between the length of the hollow computed in the current hydrodynamic manner and the length of the hollow resulting from the simplified geometric approach of Doctors and Day (2000), for example. At the very minimum, the general trend of the variation of the length of the hollow with the Froude number is properly predicted, but would seem to be rather too high. It is also vital to point out the obvious fact, with regard to Figure 8, that the experimental data is at least as subject to debate as the theoretical calculations. The length of the hollow was determined by means of a visual observation using a wire mesh as a reference frame. The accurate location of the rooster tail of the hollow xholl was not possible because of various factors; it would even seem that the definition of this length itself poses a major difficulty. CONCLUDING REMARKS The present research has been instructive in showing that the precise length of the hollow behind the transom stern is not critical to predicting the resistance, sinkage and trim, of the vessel. In many ways, this is quite remarkable, because the the authoritative version for attribution.

About this PDF file: This new digital representation of the original work has been recomposed from XML files created from the original paper book, not from the original typesetting files. Page breaks are true to the original; line lengths, word breaks, heading styles, and other typesetting-specific formatting, however, cannot be retained, and some typographic errors may have been accidentally inserted. Please use the print version of this publication as STEADY-STATE HYDRODYNAMICS OF HIGH-SPEED VESSELS WITH A TRANSOM STERN 200 flow of the water in the region of the hollow must surely affect the pressure distribution on the hull itself. There should be a resulting influence on the behavior of the vessel. It now appears that the principal features of the hollow can indeed be modeled in the simplified manner, allowing one to find (within engineering accuracy) the essential hydrodynamic performance factors of interest. Figure 4: Resistance Components (a) Lego Ship Model Figure 4: Resistance Components (b) Lego Ship Model 7 8 Figure 4: Resistance Components (c) Lego Ship Model Figure 4: Resistance Components (d) Lego Ship Model 11 12 Other models for the profile of the hollow have been considered. For example, it is thought that an S-shaped profile might also be worthy of study. Here, one end of the S corresponds to the springing point from the bottom of the transom and the other end corresponds to the rooster tail. Both ends of the S would be horizontal in this alternative model. It is necessary to emphasize that, at least with regard to resistance, the current approach still uses a traditional estimator for the frictional component. That is, ideally, one might consider utilizing a form factor to correct the frictional resistance. Alternatively, and preferably, a more sophisticated approach could be considered. That is, the influence of the actual geometry of the hull on the frictional resistance would be computed. Such an approach would take into account the non- zero pressure gradient on the surface of the hull and would be consistent with the current thin-ship theory. Finally, it would be feasible to incorporate the influence of the deformation of the free-surface on the actual submerged volume of the vessel. This the authoritative version for attribution.

About this PDF file: This new digital representation of the original work has been recomposed from XML files created from the original paper book, not from the original typesetting files. Page breaks are true to the original; line lengths, word breaks, heading styles, and other typesetting-specific formatting, however, cannot be retained, and some typographic errors may have been accidentally inserted. Please use the print version of this publication as STEADY-STATE HYDRODYNAMICS OF HIGH-SPEED VESSELS WITH A TRANSOM STERN 201 could be effected approximately by means of a local vertical distortion of the sectional geometry. The resulting influence may well be of similar significance to that of permitting the vessel to find its equilibrium. Figure 5: Comparison of Resistance (a) Lego Ship Figure 5: Comparison of Resistance (b) Lego Ship Model 7 Model 8 Figure 5: Comparison of Resistance (c) Lego Ship Figure 5: Comparison of Resistance (d) Lego Ship Model 11 Model 12 ACKNOWLEDGMENTS The authors would like to thank the Directorate of Naval Platform Systems Engineering, Department of Defence, for its support through Contract 9627MZ. They also gratefully acknowledge the assistance of the Australian Research Council (ARC) Large Grant Scheme (via Grant Number A89917293). The support of this work by The University of New South Wales is also greatly appreciated. REFERENCES COUSER, P.R., WELLICOME, J.F., AND MOLLAND, A.F.: “An Improved Method for the Theoretical Prediction of the Wave Resistance of Transom- Stern Hulls Using a Slender Body Approach”, International Shipbuilding Progress, Vol. 45, No. 444, pp 331–349 (December 1998) DAY, A.H. AND DOCTORS, L.J.: “Design of Fast Ships for Minimal Resistance and Motions”, Proc. Sixth International Marine Design Conference (IMDC '97), Newcastle upon Tyne, England, pp 569–583 (June 1997) DAY, A.H. AND DOCTORS, L.J.: “Resistance Optimization of Displacement Vessels on the Basis of Principal Parameters”, J. Ship Research, Vol. 41, No. 4, pp 249–259 (December 1997) the authoritative version for attribution.

About this PDF file: This new digital representation of the original work has been recomposed from XML files created from the original paper book, not from the original typesetting files. Page breaks are true to the original; line lengths, word breaks, heading styles, and other typesetting-specific formatting, however, cannot be retained, and some typographic errors may have been accidentally inserted. Please use the print version of this publication as STEADY-STATE HYDRODYNAMICS OF HIGH-SPEED VESSELS WITH A TRANSOM STERN 202 Figure 6: Comparison of Sinkage (a) Lego Ship Model 7 Figure 6: Comparison of Sinkage (b) Lego Ship Model 8 Figure 6: Comparison of Sinkage (c) Lego Ship Model Figure 6: Comparison of Sinkage (d) Lego Ship Model 11 12 DAY, A.H., DOCTORS, L.J., AND ARMSTRONG, N.A.: “Concept Evaluation for Large Very-High-Speed Vessels”, Proc. Fourth International Conference on Fast Sea Transportation (FAST '97), Sydney, Australia, Vol. 1, pp 65–75 (July 1997) DE PRIMA, C.R. AND WU, T.Y.: “On the Theory of Surface Waves in Water Generated by Moving Disturbances”, California Institute of Technology, Engineering Division, Pasadena, California, Report 21–23, 40+i pp (May 1957) DOCTORS, L.J.: “Modifications to the Michell Integral for Improved Prediction of Ship Resistance”, Proc. Twenty-Seventh Israel Conference on Mechanical Engineering, Technion, Haifa, Israel, pp 502–506 (May 1998) DOCTORS, L.J.: “Improvement of the Correlation of Michell's Integral for Displacement Vessels”, Proc. Third Biennial Engineering Mathematics and Applications Conference (EMAC '98), Adelaide, South Australia, pp 183–187 (July 1998) DOCTORS, L.J.: “Intelligent Regression of Resistance Data for Hydrodynamics in Ship Design”, Proc. Twenty-Second Symposium on Naval Hydrodynamics, Washington, DC, pp 33–48, Discussion: 49 (August 1998) DOCTORS, L.J.: “An Improved Theoretical Model for the Resistance of a Vessel with a Transom Stern”, Proc. Thirteenth Australasian Fluid Mechanics Conference (13 AFMC), Monash University, Melbourne, Victoria, Vol. 1, pp 271–274 (December 1998) DOCTORS, L.J.: “On the Great Trimaran-Catamaran Debate”, Proc. Fifth International Conference on Fast Sea Transportation the authoritative version for attribution.

About this PDF file: This new digital representation of the original work has been recomposed from XML files created from the original paper book, not from the original typesetting files. Page breaks are true to the original; line lengths, word breaks, heading styles, and other typesetting-specific formatting, however, cannot be retained, and some typographic errors may have been accidentally inserted. Please use the print version of this publication as STEADY-STATE HYDRODYNAMICS OF HIGH-SPEED VESSELS WITH A TRANSOM STERN 203 (FAST '99), Seattle, Washington, pp 283–296 (August–September 1999) DOCTORS, L.J. AND BECK, R.F.: “Convergence Properties of the Neumann-Kelvin Problem for a Submerged Body”, J. Ship Research, Vol. 31, No. 4, pp 227–234 (December 1987) DOCTORS, L.J. AND DAY, A.H.: “Hydrodynamically Optimal Hull Forms for River Ferries”, Proc. International Symposium on High-Speed Vessels for Transport and Defence, Royal Institution of Naval Architects, London, England, pp 5–1–5–15 (November 1995) DOCTORS, L.J. AND DAY, A.H.: “Resistance Prediction for Transom-Stern Vessels”, Proc. Fourth International Conference on Fast Sea Transportation (FAST '97), Sydney, Australia, Vol. 2, pp 743–750 (July 1997) DOCTORS, L.J. AND DAY, A.H.: “The Squat of a Vessel with a Transom Stern”, Proc. Fifteenth International Workshop on Water Waves and Floating Bodies (15 IWWWFB), Caesarea, Israel, pp 40–43 (February–March 2000) DOCTORS, L.J. AND RENILSON, M.R.: “The Influence of Demihull Separation and River Banks on the Resistance of a Catamaran”, Proc. Second International Conference on Fast Sea Transportation (FAST '93), Yokohama, Japan, Vol. 2, pp 1231–1244 (December 1993) LEWIS, E.V. (ED.): Principles of Naval Architecture: Volume II. Resistance, Propulsion and Vibration, Society of Naval Architects and Marine Engineers, Jersey City, New Jersey, 327+vi pp (1988) Figure 7: Comparison of Trim (a) Lego Ship Model 7 Figure 7: Comparison of Trim (b) Lego Ship Model 8 Figure 7: Comparison of Trim (c) Lego Ship Model 11 Figure 7: Comparison of Trim (d) Lego Ship Model 12 LUNDE, J.K.: “On the Linearized Theory of Wave Resistance for Displacement Ships in Steady and the authoritative version for attribution.

About this PDF file: This new digital representation of the original work has been recomposed from XML files created from the original paper book, not from the original typesetting files. Page breaks are true to the original; line lengths, word breaks, heading styles, and other typesetting-specific formatting, however, cannot be retained, and some typographic errors may have been accidentally inserted. Please use the print version of this publication as STEADY-STATE HYDRODYNAMICS OF HIGH-SPEED VESSELS WITH A TRANSOM STERN 204 Accelerated Motion”, Trans. Society of Naval Architects and Marine Engineers, Vol. 59, pp 25–76, Discussion: 76–85 (December 1951) MICHELL, J.H.: “The Wave Resistance of a Ship”, Philosophical Magazine, London, Series 5, Vol. 45, pp 106–123 (1898) MOLLAND, A.F., WELLICOME, J.F., AND COUSER, P.R.: “Resistance Experiments on a Systematic Series of High Speed Displacement Catamaran Forms: Variation of Length-Displacement Ratio and Breadth-Draught Ratio”, University of Southampton, Department of Ship Science, Report 71, 82+i pp (March 1994) NEWMAN, J.N.: Marine Hydrodynamics, The MIT Press, Cambridge, Massachusetts, 402+xiii pp (1980) RAYLEIGH, LORD: “The Form of Standing Waves on the Surface of Running Water”, Proc. London Math. Society, Vol. 15, pp 69–78 (December 1883) SAHOO, P.K., DOCTORS, L.J., AND RENILSON, M.R.: “Theoretical and Experimental Investigation of Resistance of High-Speed Round-Bilge Hull Forms”, Proc. Fifth International Conference on Fast Sea Transportation (FAST '99), Seattle, Washington, pp 803–814 (August–September 1999) SRETENSKY, L.N.: “On the Wave-Making Resistance of a Ship Moving along in a Canal”, Philosophical Magazine, Series 7, Supplement, Vol. 22, No. 150, pp 1005–1013 (November 1936) WEHAUSEN, J.V. AND LAITONE, E.V.: “Surface Waves”, Encyclopedia of Physics: Fluid Dynamics III, Ed. by S.Flügge, Springer-Verlag, Berlin, Vol. 9, pp 445–814 (1960) Figure 8: Comparison of Hollow Length (a) Lego Ship Figure 8: Comparison of Hollow Length (b) Lego Ship Model 7 Model 8 Figure 8: Comparison of Hollow Length (c) Lego Ship Figure 8: Comparison of Hollow Length (d) Lego Ship Model 11 Model 12 the authoritative version for attribution.

About this PDF file: This new digital representation of the original work has been recomposed from XML files created from the original paper book, not from the original typesetting files. Page breaks are true to the original; line lengths, word breaks, heading styles, and other typesetting-specific formatting, however, cannot be retained, and some typographic errors may have been accidentally inserted. Please use the print version of this publication as STEADY-STATE HYDRODYNAMICS OF HIGH-SPEED VESSELS WITH A TRANSOM STERN 205 DISCUSSION L.Raheja Indian Institute of Technology, India It was a nice presentation. It is not a question but more of a comment. It seems that the primary reason or motivation for using such a simplified model (i.e. centerplane source distribution) is because it is expected or presumed that the wave drag will be much smaller than the frictional part. I propose that the model could be improved upon by using a desingularized panel method where the sources could be placed little inside the boundary which would still preserve the simplified calculation aspect and may work better in the sense of diluting the presumption. AUTHOR'S REPLY I appreciate your comment, Since we were getting good results in this case, so we continued with the model. However, we may improve upon it in subsequent work. Thank you very much for your question. the authoritative version for attribution.

Next: Practical CFD Applications to Design of a Wave Cancellation Multihull Ship »
Twenty-Third Symposium on Naval Hydrodynamics Get This Book
×
Buy Paperback | $550.00
MyNAP members save 10% online.
Login or Register to save!
Download Free PDF

"Vive la Revolution!" was the theme of the Twenty-Third Symposium on Naval Hydrodynamics held in Val de Reuil, France, from September 17-22, 2000 as more than 140 experts in ship design, construction, and operation came together to exchange naval research developments. The forum encouraged both formal and informal discussion of presented papers, and the occasion provides an opportunity for direct communication between international peers.

This book includes sixty-three papers presented at the symposium which was organized jointly by the Office of Naval Research, the National Research Council (Naval Studies Board), and the Bassin d'Essais des Carènes. This book includes the ten topical areas discussed at the symposium: wave-induced motions and loads, hydrodynamics in ship design, propulsor hydrodynamics and hydroacoustics, CFD validation, viscous ship hydrodynamics, cavitation and bubbly flow, wave hydrodynamics, wake dynamics, shallow water hydrodynamics, and fluid dynamics in the naval context.

  1. ×

    Welcome to OpenBook!

    You're looking at OpenBook, NAP.edu's online reading room since 1999. Based on feedback from you, our users, we've made some improvements that make it easier than ever to read thousands of publications on our website.

    Do you want to take a quick tour of the OpenBook's features?

    No Thanks Take a Tour »
  2. ×

    Show this book's table of contents, where you can jump to any chapter by name.

    « Back Next »
  3. ×

    ...or use these buttons to go back to the previous chapter or skip to the next one.

    « Back Next »
  4. ×

    Jump up to the previous page or down to the next one. Also, you can type in a page number and press Enter to go directly to that page in the book.

    « Back Next »
  5. ×

    To search the entire text of this book, type in your search term here and press Enter.

    « Back Next »
  6. ×

    Share a link to this book page on your preferred social network or via email.

    « Back Next »
  7. ×

    View our suggested citation for this chapter.

    « Back Next »
  8. ×

    Ready to take your reading offline? Click here to buy this book in print or download it as a free PDF, if available.

    « Back Next »
Stay Connected!